Most injuries in home service work don't come from exotic hazards. They come from the same few things done in a hurry: a ladder set on soft ground, an attic with no light and exposed nails, a ceiling fan wired with the breaker on. A job safety analysis (JSA) is a simple way to slow down once, on paper, and decide how a job will be done safely every time after that.

This free JSA template follows the method in OSHA's booklet Job Hazard Analysis (publication 3071). It has a blank form for your own jobs and a second page with a filled-in example for extension ladder work. Download it as an editable Word document or a printable PDF with the buttons above.

What is a job safety analysis?

OSHA describes a job hazard analysis as "a technique that focuses on job tasks as a way to identify hazards before they occur." It looks at the relationship between the worker, the task, the tools and the work environment. You break the job into steps, ask what can go wrong at each step, and decide how to remove or control each hazard.

Job safety analysis (JSA), job hazard analysis (JHA) and task hazard analysis are names for the same idea. OSHA's booklet uses "job hazard analysis" in its title and "job safety analysis" in its text.

A JSA is useful in three ways for a small contractor:

  • It finds hazards before someone gets hurt, instead of after.
  • It becomes your training sheet. OSHA points out that the analysis can be a valuable tool for training new employees in the steps of the job.
  • It shows customers and general contractors you take safety seriously. Some commercial clients and GCs ask subs for a JSA or JHA before work starts.

Is a JSA required by OSHA?

Not as a general rule. OSHA publication 3071 is a guidance booklet, and it doesn't set out a required form. It does say that the OSHA standards for your industry are mandatory, and that building their requirements into your analysis helps make sure your program meets them.

Some standards do require a written hazard assessment for a specific purpose. In general industry, for example, 29 CFR 1910.132(d) requires the employer to assess the workplace for hazards that call for personal protective equipment, select the right PPE, and verify the assessment with a written certification that names the workplace, the person certifying and the date. A JSA can cover much of that thinking, but if a standard requires a specific document, make sure you have that document.

Also check whether your state runs its own OSHA-approved State Plan. OSHA lists 29 State Plans; they must be at least as effective as federal OSHA and can have their own rules. If a client's contract requires a JSA, follow the contract's format.

What's in the JSA template

Page 1 is the blank form:

  • Your business details, a JSA number, date, job number and a review date
  • The job: task, location, work area (attic, roof, crawlspace) and the tools and equipment used
  • Who prepared it: the analyst, supervisor and crew involved, and why the JSA was written (new task, changed task, after an injury or near miss, periodic review)
  • Required PPE checkboxes
  • The analysis table: step number, job step, hazards (what can go wrong), controls, and who is responsible for each control
  • Before work starts: emergency information (nearest hospital, first aid kit, who calls 911) and permits, locates or lockout needed
  • Signatures for the supervisor, and a line for the crew to initial that the JSA was reviewed with them

Page 2 is the filled-in example below. Replace everything in [square brackets] with your own details.

How to write a JSA, step by step

These steps follow OSHA publication 3071.

1. Pick the job. OSHA suggests giving priority to jobs with the highest injury or illness rates; jobs that could cause severe or disabling injuries even if nothing has happened yet; jobs where one simple human error could lead to a severe injury; jobs that are new or have changed; and jobs complex enough to need written instructions. For most home service companies, that list starts with ladder and roof work, attic and crawlspace work, electrical work and anything involving lifting heavy equipment.

2. Involve the people who do the job. OSHA calls this very important: the crew knows where the hazards are, and people follow procedures they helped write.

3. Review what has gone wrong before. Look at past injuries, damaged equipment and near misses on this job. OSHA treats these as signs that existing controls may not be enough.

4. Fix immediate dangers now. If you find something that threatens someone's life or health, OSHA says to act right away instead of waiting for the analysis to be finished.

5. Break the job into steps. Watch someone do the job and write each step as they do it. OSHA's advice: enough detail to describe each action, but not so much that the list becomes too long, and not so broad that it skips basic steps. Five to ten steps covers most service tasks. Tell the worker you're evaluating the job, not their performance.

6. Ask the hazard questions for each step. OSHA's list:

  • What can go wrong?
  • What are the consequences?
  • How could it arise?
  • What are other contributing factors?
  • How likely is it that the hazard will occur?

Write hazards as specific scenarios. "Ladder slides out at the base on wet grass, worker falls about 12 feet" leads to a control. "Falls" doesn't.

7. Choose controls, best first. OSHA's booklet ranks controls in this order: engineering controls (remove the hazard, substitute something safer, enclose or isolate it, ventilate), then administrative controls (written procedures, safe work practices, time limits, warnings, a buddy system, training), then personal protective equipment. PPE is the last line of defense: OSHA lists it as acceptable when engineering controls aren't feasible or don't fully eliminate the hazard, while they're being put in place, when safe work practices don't give enough protection, and in emergencies. In practice, most jobs use a mix of all three.

8. Check the OSHA standards for the task. Ladders, fall protection, electrical work, respirators and PPE all have specific rules. Write their requirements into your controls.

9. Review it with the crew, then use it. Go through the JSA before the job, have the crew initial it, and keep it in the truck or in your job folder.

10. Review and update it. OSHA recommends periodic reviews, and especially after an injury or illness on that job. Even if nothing has changed, a fresh look often finds a hazard the first pass missed. Train everyone affected whenever you change it.

Job safety analysis example: extension ladder work

Here's the example from page 2 of the template, for setting up and using an extension ladder to reach a gutter or roof edge at a two-story house. It uses generic controls drawn from OSHA's ladder rules; adapt it to your ladder, your site and the standards that apply to your work. It's an example, not a complete safety program.

Job: Set up and use an extension ladder at a two-story house. PPE: safety glasses, work gloves, slip-resistant boots.

# Job step Hazards (what can go wrong) Controls
1 Inspect the ladder Cracked rail, bent or loose rung, worn feet or broken lock makes the ladder fail under load Inspect rails, rungs, feet, locks and labels before use; tag a damaged ladder "Do not use" and take it out of service. Check the duty rating covers the worker plus tools and materials.
2 Plan the placement Ladder or worker contacts overhead power lines (electrocution); ladder set in a doorway or walkway gets bumped Look up before carrying or raising the ladder; choose a spot well clear of the service drop and other lines; use a ladder with nonconductive side rails (fiberglass) where it could contact energized equipment. Keep the area at the top and bottom clear; block or lock a door the ladder stands in front of.
3 Carry and raise the ladder Back strain; ladder gets away and strikes a person, window or line Two people for long or heavy ladders; raise it near its final spot; keep it under control and away from lines while raising.
4 Set the ladder Base slides out on wet grass or a slope; ladder tips sideways; worker can't step safely onto the roof Firm, level footing or secure the ladder against displacement; set the base out about 1 foot for every 4 feet of working length; extend the rails at least 3 feet above the roof edge when stepping off onto the roof; tie off or have someone foot the ladder where it could shift.
5 Climb and work Fall from losing balance, overreaching or carrying a load; dropped tools hit someone below Face the ladder and keep at least one hand on it while climbing; carry tools on a belt or raise them with a line or bucket, not in your hands; keep your body between the rails and move the ladder instead of reaching; keep people out of the area below.
6 Clean out debris Cuts from sharp gutter edges and fasteners; debris in eyes; stinging insects Cut-resistant gloves and safety glasses; look for nests before reaching in.

Where the example comes from: OSHA's construction ladder rule (29 CFR 1926.1053) requires ladders used to reach an upper landing to extend at least 3 feet above it (or be secured at the top with a grab rail when that isn't possible), non-self-supporting ladders to be set so the base is about one-quarter of the working length out from the top support, stable and level footing unless the ladder is secured, a clear area at the top and bottom, nonconductive side rails where the worker or ladder could contact exposed energized electrical equipment, facing the ladder and keeping at least one hand on it while climbing, and no carrying of loads that could make the worker lose balance. OSHA's general industry ladder rule (29 CFR 1910.23) also requires ladders to be inspected before initial use in each work shift. OSHA's own list of common hazards uses this very case as an example of an electrical hazard: a metal ladder that contacts power lines.

JSA ideas for home service jobs

Write one JSA per task, not per trade. Good candidates:

  • HVAC: attic air handler service (heat, poor footing between joists, exposed nails, insulation dust), rooftop unit service (falls from roof edges, lifting), refrigerant recovery (pressurized cylinders, frostbite).
  • Electrical: panel work and circuit replacement (shock and arc flash; lockout and verifying the circuit is dead), crawlspace wiring (confined, wet, pests).
  • Plumbing: water heater replacement (lifting, scalding water, gas), drain cleaning with a machine (rotating cable, sewage exposure).
  • Roofing: tear-off and loading (falls, struck-by from debris, heat), material delivery to the roof.
  • Painting: exterior prep and painting from ladders, sanding and paint removal on older homes (lead dust).
  • Cleaning and pest control: mixing and applying chemicals (read the safety data sheet and the product label), moving furniture.

Each of these has OSHA standards behind it. If you're not sure which apply, OSHA's On-Site Consultation program gives free, confidential safety help to small and medium-sized businesses, separate from enforcement. OSHA's booklet also lists your insurance company and private safety consultants as sources of help.

Put the JSA to work

A JSA filed in a drawer doesn't prevent anything. Make it part of how jobs run:

  • Attach it to the work order. Note the JSA number on the work order for tasks that have one, so the technician sees it before the visit.
  • Require it from subs on your jobs. Our subcontractor agreement template already makes subcontractors responsible for complying with OSHA and your project's safety requirements; asking for a JSA on higher-risk tasks is a simple way to check.
  • Use it to train new hires. Walk a new technician through the JSA before their first job of that type.
  • Bring it up after a near miss. A close call is the cheapest lesson you'll get. Review the JSA with everyone who does the job.

Starting out? Safety planning belongs in the early checklist with licensing and insurance; see our guides on how to start a roofing business and how to start an HVAC business.